Lanner LEC-3110 Manuel d'utilisateur

>>Embedded & Industrial ComputingHardware Platforms for Embedded and Industrial ComputingLEC-3110Version 1.0User's ManualPublication d

8Motherboard InformationChapter 3Embedded and Industrial ComputingChapter 3: Motherboard InformationBlock DiagramThe block diagram depicts the r

9Motherboard InformationChapter 3Embedded and Industrial ComputingMotherboard LayoutThe motherboard layout shows the connectors and jumpers on

10Motherboard InformationChapter 3Embedded and Industrial ComputingJumper SettingsSATA Connector (J10, J11): The system supports one SATA driv

11Motherboard InformationChapter 3Embedded and Industrial ComputingSW1/SW3 (on LEB-3110) and SW1/SW2/SW3/SW4/SW9/SW10/SW11/SW112 (on LEK-COM08): Thes

12Motherboard InformationChapter 3Embedded and Industrial ComputingPin No. Description Pin No. Description1 Red Color Signal 6 Ground2 Green Color Sig

13Motherboard InformationChapter 3Embedded and Industrial ComputingFront LED Connector (J3 on LEK-COM08): This is the parallel connector for t

14Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AAppendix A: Programming Watchdog TimerA watchdog timer is a piece of ha

15Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AChoose to select the hardware Manually8. Choose Show all device and click Next.

16Programming Watchdog TimerEmbedded and Industrial ComputingAppendix ASelect the Lanner IO driver and click Next.14. Click Next15. Click 16. Complet

17Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AWatch Dog sample code:// LEC3xxx_Test.cpp : Defines the entry point for the con

TTaTTable of Contentsbeable of ContentsiChapter 1: Introduction 1System Specication . . . . . . . . . . . . . . . . . . . . .

18Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A Run_LED (0, 0) ; Run_LED (1, 0) ; } else if (argv[1][0] == ‘3’)

19Driver InstallationAppendix BNetwork Application PlatformsAppendix B: Driver InstallationChipset Driver InstallationTo install the Intel® chip

20Driver InstallationAppendix BNetwork Application PlatformsLAN Adapters Driver InstallationThis section provides the instructions on how to

21Driver InstallationAppendix BNetwork Application PlatformsOn LinuxFollow these instructions when installing the Intel® LAN controller base dr

22Driver InstallationAppendix BNetwork Application PlatformsVGA Driver InstallationOn the Windows OSThis section provides the instructions on h

23Terms and ConditionsAppendix CEmbedded and Industrial ComputingAppendix C: Terms and ConditionsWarranty Policy All products are under warran

24Terms and ConditionsAppendix CEmbedded and Industrial ComputingRMA Service Request Form When requesting RMA service, please fill out the following

1IntroductionChapter 1Embedded and Industrial ComputingChapter 1: IntroductionThe LEC-3110 embedded platform was built on the Intel D525 processor a

2IntroductionChapter 1Embedded and Industrial ComputingPackage ContentsYour package contains the following items:LEC-3110 Embedded System •Rack Mounti

3IntroductionChapter 1Embedded and Industrial ComputingF7F1 CTRThis is a software reset switch which could be programmed to reset your application to

4IntroductionChapter 1Embedded and Industrial ComputingRear Panel FeaturesR1 VGA ConnectorThe VGA is provided by the integrated GPU which implements

5IntroductionChapter 1Embedded and Industrial ComputingThis terminal block can be connected as 8 Com ports with serial port type of RS-232, R

6IntroductionChapter 2Embedded and Industrial ComputingChapter 2: Hardware SetupPreparing the Hardware InstallationTo access some components and perf

7IntroductionChapter 2Embedded and Industrial ComputingInstalling a CompactFlash CardLEC-3110 provides one CompactFlash slot. Follow the procedu