Lanner LEC-2026 Manuel d'utilisateur

LEC-2026 Manual

LEC-2026 10 2.1.2 Dimensions (mm) Figure 3 – Dimensions

LEC-2026 11 2.1.3 Jumper Settings and I/O Connectors This section lists jumper settings and I/O connectors of the MB-7530 board which are specif

LEC-2026 12 2.1.4 Connectors Pin Assignment J4: Clear CMOS connector Pin Description 1 RTCRSTS# 2 RTC_RST# 3 GND J5：Adapter Jack connector

LEC-2026 13 J6: VGA Connector(Pin Header 2x6 2.54mm) PIN Description PIN Description 1 CRT_R 2 CRT_ON 3 CRT_G 4 GND 5 CRT_B 6 GND 7 HSYNC_1 8 GND

LEC-2026 14 J8/J9: SATA connector Pin Description Pin Description 1 GND 1 GND 2 SATA0TX+ 2 SATA2TX+ 3 SATA0TX- 3 SATA2TX- 4 GND 4 GND 5 S

LEC-2026 15 J11: COM port Pin Header (2x5 2.54mm) Pin Description Pin Description 1 CMA2_1 2 CMA2_2 3 CMA2_3 4 CMA2_4 5 CMA2_5 6 CMA2_6 7 CMA2_

LEC-2026 16 SW1：Reset Bottom Pin Description 1 SYS_RST# 2 GND 3 GND 4 GND SW2: Power on Switch Pin Description PAD1 GND PAD2 GND 1 5VSB 2 5V

LEC-2026 17 COM1: Console Serial Port A Connector(RJ-45) Pin Description 1 CMA1_4 2 CMA1_7 3 CMA1_5 4 BP_GND 5 BP_GND 6 CMA1_3 7 CMA1_2 8 CMA1_6

LEC-2026 18 CON2：SATA Power On Connector(WAFER 4P 2.54mm) Pin Description 1 VCC12 2 GND 3 GND 4 VCC5 USB1: USB connector 8P 2.54mm

LEC-2026 19 CN2: Compact flash connector Pin Description Pin Description 1 GND 26 CD1_1- 2 PDD3 27 PDD11 3 PDD4 28 PDD12 4 PDD5 29 PDD13 5

LEC-2026 2 LEC-2026 Manual Copyright 2007, Lanner Electronics, Inc. All rights reserved. This document contains proprietary information

LEC-2026 20 CONN1: Reset Connector(Pin Header 1x2 2.54mm) Pin Description 1 N40412059 2 GND CON1: Mini-PCI connector

LEC-2026 21 Pin Description Pin Description Pin Description Pin Description 1 NC 63 VCC3 2 NC 64 FRAME# 3 NC 65 TP 4 NC 66 TRDY# 5 NC 67 SERR# 6

LEC-2026 22 CN1: DDRII socket SO-DIMM 200P Pin Description Pin Description Pin Description Pin Description Pin Description1

LEC-2026 23 29 DQSA#1 69 X 109 SWEA# 149 GND 189 MDA58 30 DCLK0 70 DQSA3 110 CS#0 150 GND 190 GND 31 DQSA1 71 GND 111 VCC 151 MDA42

LEC-2026 24 LAN1-LAN2: RJ-45 LAN connector (provided by Intel 82574L, Bypass Pair) Pin Description Pin Description 1 P1_MDXP0 8 P1_MDXN3 2 P1

LEC-2026 25 2.2 The Front and Back Panel This section describes the front and back panel of LEC-2026. Figure 4 － LEC-2026 Front View • Con

LEC-2026 26 3. Hardware Installation Guide 3.1 Open the Chassis Step1: Unscrew these 4 rubber screws on the bottom of the system as shown in the a

LEC-2026 27 3.2 System Memory Use the following procedure to install the DDR2 RAM Step 1: Position the DIMM module alongside the DIMM socket at 45

LEC-2026 28 3.3 Install the Compact Flash Card Insert the Compact Flash card into the CF slot with the arrow pointing toward the socket as shown i

LEC-2026 29 4. BIOS Setup BIOS Setup AMI’s ROM BIOS provides a built-in Setup program that allows users to modify the basic system configuration and

LEC-2026 3 Safety Guidelines Follow these guidelines to ensure general safety: z Keep the chassis area clear and dust-free during and after installa

LEC-2026 30 4.1 Main Program Screen This screen provides access to the utility‘s various functions. Listed below is explanation of the keys displa

LEC-2026 31 4.2 Main CMOS Setup When you select the “Main CMOS SETUP” on the main program, the screen display will appears as: The Main CMOS Setu

LEC-2026 32 4.3 Advanced Menu When you select the “Advanced Menu” on the main program, the screen display will appear as: The following explains t

LEC-2026 33 ATA/IDE Configuration: These 2 items allow you to select the ATA/IDE and SATA configuration. Select [Disabled] in ATA/IDE Configuration i

LEC-2026 34 (Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring). These values are not user-configurabl

LEC-2026 35 device is accessed through BIOS. Configuration options: [Disabled] [Enabled]. IDE Detect Time Out (Sec): Select the time out value for

LEC-2026 36 ATA(PI) 80Pin Cable Detection: Select the mechanism for detecting 80Pin ATA(PI) cable. Configuration options: [Host Device] [Host] [Devic

LEC-2026 37 Serial Port1/2 Address: These items specify the base I/O port addresses of the onboard Serial Port 1 Selecting [Auto] allows BIOS to auto

LEC-2026 38 Serial Port2 Mod: These items specify the onboard Serial Port 2 mod. Selecting [Normal] allows BIOS to automatically determine the Normal

LEC-2026 39 Parallel Port Mode: Allows you to select the Parallel Port mode. Configuration options: [Normal] [Bi-directional] [EPP] [ECP] [ECP &

LEC-2026 4 EMC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

LEC-2026 40 Restore on AC power Loss: Allows you to select the Restore on AC power Loss. Configuration options: [Power off] [Power on]. Hardware H

LEC-2026 41 USB Configuration: Press <Enter> to enter the sub-menu and the following screen appears: Legacy USB Support: Enables support f

LEC-2026 42 Port 64/60 Emulation: Configures the USB Port 64/60 Emulation This option enables/disables the “Port 60h/64h” trapping option. Port 60h/6

LEC-2026 43 BIOS EHCI Hand-Off: this is a workaround for Os without EHCI hand-off support. The EHCI ownership change should claim by EHCI driver. Con

LEC-2026 44 USB MASS Storage Reset Delay: Number of seconds POST waits for the USB mass Storage device after start unit command. Configuration option

LEC-2026 45 Remote Access Configuration: Press <Enter> to enter the sub-menu and enable Remote Access then the following screen appears: Config

LEC-2026 46 Serial Port Mode: Select Serial Port resolution setting. Configuration options: [115200 8,n, 1][57600 8,n, 1][38400 8,n, 1][19200 8,n, 1]

LEC-2026 47 Redirection After BIOS POST: DISABLE, Turns off the redirection after POST. Boot Loader, Redirection is active during POST and during Boo

LEC-2026 48 VT-UTF8 Combo Key Support: Enable VT-UTF8 Combination Key Support for ANSI/VT100 terminals. Configuration options: [Enabled][Disabled]

LEC-2026 49 Restore on AC Power Loss: Lan ByPass: Allow you to select Bypass function. Configuration options: [Disabled] [Enabled].

LEC-2026 5 Contents Safety Guidelines ... 3 EMC Notice ...

LEC-2026 50 Lan By Pass when power off: Allow you to select Bypass function when System power off . Configuration options: [Disabled] [Enabled]. On

LEC-2026 51 4.4 Boot Menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the su

LEC-2026 52 Quick Boot : Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot

LEC-2026 53 Add On ROM Display Mode: Sets the display mode for option ROM. Configuration options: [Force BIOS] [Keep Current]. Bootup Num-Lock: All

LEC-2026 54 PS/2 Mouse Support: Allows you to enable or disable support for PS/2 mouse. Configuration options: [Disabled] [Enabled] [Auto]. Wait fo

LEC-2026 55 Hit ‘DEL’ Message Display: When set to Enabled, the system displays the message “Press DEL to run Setup” during POST. Configuration opt

LEC-2026 56 Boot Device Priority: Press <Enter> to enter the sub-menu and the following screen appears: 1st ~ xxth Boot Device: These items

LEC-2026 57 4.5 Security Menu Press <Enter> to enter the sub-menu and the following screen appears: Type the password, up to 6 characters i

LEC-2026 58 4.6 Exit Menu Press <Enter> to enter the sub-menu and the following screen appears: Save Changes and Exit: Once you are finishe

LEC-2026 59 Discard Changes and Exit: Select this option only if you do not want to save the changes that you made to the Setup program. If you made

LEC-2026 6 1. Product Overview 1.1 Product Introduction Figure 1 － LEC-2026 Outlook Based on the Intel Atom N270 Mobile Processor, the LEC-2026 m

LEC-2026 60 Load Optimal/Failsafe Defaults: This option allows you to load the default values for each of the parameters on the Setup menus. When you

LEC-2026 61 Appendix A: Watchdog Timer Most systems need to be self-reliant. If an error should occur it is typically not possible to wait for the s

LEC-2026 62 Appendix B: Console Redirection Console redirection lets you maintain a system from a remote location by re-directing keyboard input an

LEC-2026 63 Appendix C: LAN Bypass Function The bypass function is used to link (or short) two independent Ethernet ports when the system crash or p

LEC-2026 64 Bypass Settings System Status LAN Bypass for Port1 and Port 2 LAN Bypass 1&2 when power off Enabled Disabl

LEC-2026 65 Lanner also provides sample code for bypass control with WDT via programming. For sample code, look in the LAN_Bypass_Watchdog directory

LEC-2026 66 Terms and Conditions Date: 2011.06.29 Warranty Policy 1. All products are under warranty against defects in materials and workmanship

LEC-2026 67 RMA Service Request Form When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be

LEC-2026 7 1.3 Specifications FEATURE DESCRIPTION Form Factor Desktop Processor Intel Atom N270 1.6 GHz Max Speed 1.6 GHz Front Side Bus 533 MH

LEC-2026 8 1.4 Package Contents Carefully unpack your package and make sure that you have the below items. • LEC-2026 Embedded System x 1 • Consol

LEC-2026 9 2. System Components 2.1 MB-7530 system Board MB-7530 is the system board bundled with the LEC-2026 embedded system. The succeeding sect