Lanner LEC-7100 Manuel d'utilisateur

>>Embedded & Industrial ComputingHardware Platforms for Embedded and Industrial ComputingLEC-7100User's ManualPublication date:2010-05

7Motherboard InformationChapter 3Embedded and Industrial ComputingChapter 3: Motherboard InformationBlock DiagramThe block diagram depicts the re

8Motherboard InformationChapter 3Embedded and Industrial ComputingMotherboard LayoutThe motherboard layout shows the connectors and jumpers on

9Motherboard InformationChapter 3Embedded and Industrial ComputingJumper SettingsM1Power/Hard Disk LED (LED1): The power and hard disk LED indicator.M

10Motherboard InformationChapter 3Embedded and Industrial ComputingM9RS-232 COM Port(COM1, CN18): It is the RS-232 serial port. M10SO-DIMM Socket (CN8

11Motherboard InformationChapter 3Embedded and Industrial ComputingM17Power Switch through Phoenix Contact(J12)M18DIO Ports(CN14): The 8 pins of Gener

12Motherboard InformationChapter 3Embedded and Industrial ComputingPIN NO. Description Pin No. Description115 SYS_AUDIO_OUT 116 SYS_AUDIO_IN 117 SY

13Bios SettingsChapter 4Embedded and Industrial ComputingChapter 4: BIOS SettingsAccessing the BIOS menuUse the BIOS Setup program when you ar

14Bios SettingsChapter 4Embedded and Industrial ComputingThe Main MenuThe main BIOS setup menu is the first screen that you can navigate. Each main BI

15Bios SettingsChapter 4Embedded and Industrial ComputingOption DescriptionDisabled Set this value to allow the hard disk drive to be used n

16Bios SettingsChapter 4Embedded and Industrial ComputingPrimary and Secondary IDE Master and Slave SettingsFrom the IDE Configuration screen, pr

iAboutAboutEmbedded and Industrial ComputingOverviewIcon DescriptionsThe icons are used in the manual to serve as an indication of interest topics

17Bios SettingsChapter 4Embedded and Industrial ComputingNote: For drive capacities over 137 GB, your AMIBIOS must be equipped with 48-bit

18Bios SettingsChapter 4Embedded and Industrial ComputingOption DescriptionAuto Set this value to allow the BIOS to auto detect the DMA mode.

19Bios SettingsChapter 4Embedded and Industrial ComputingOption DescriptionAuto Set this value to allow the BIOS to auto detect hard disk drive

20Bios SettingsChapter 4Embedded and Industrial ComputingOption DescriptionEnabled Enable the support for the OS without EHCI Hand-Off feature.

21Bios SettingsChapter 4Embedded and Industrial ComputingACPI SettingsSelect the ACPI tab from the setup screen to enter the ACPI BIOS Setup

22Bios SettingsChapter 4Embedded and Industrial ComputingAML code during ACPI O/S operations.Option DescriptionDisabled This option disables adding

23Bios SettingsChapter 4Embedded and Industrial ComputingRemote Access ConfigurationYou can use this screen to select options for the Remote Access Co

24Bios SettingsChapter 4Embedded and Industrial ComputingYes This setting should be set if the operating system complies with the ACPI (Advanced C

25Bios SettingsChapter 4Embedded and Industrial ComputingBoot SettingsSelect the Boot tab from the setup screen to enter the Boot BIOS Setup screen. Y

26Bios SettingsChapter 4Embedded and Industrial ComputingSecurity SettingsSelect Security Setup from the Setup main BIOS setup menu. All Sec

TTaTTable of Contentsbeable of ContentsiiChapter 1: Introduction 1System Specication . . . . . . . . . . . . . . . . . . . . .

27Bios SettingsChapter 4Embedded and Industrial ComputingExit MenuSelect the Exit tab from the setup screen to enter the Exit BIOS Setup screen. You

28Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AAppendix A: Programming Watchdog TimerA watchdog timer is a piece of ha

29Programming Watchdog TimerEmbedded and Industrial ComputingAppendix Atemp |= 0x04;write_w83627_reg(0, 0x2b, temp); //set watchdog pinwrite_w83627_re

30Setting up Remote AccessAppendix BEmbedded and Industrial ComputingAppendix B: Setting up Remote AccessRemote Access lets you monitor and configure

31Digital Input/Output ControlAppendix CEmbedded and Industrial ComputingAppendix C: Digital Input/Output Control on the GPIO portThe Digitanl I/O on

32Digital Input/Output ControlAppendix CEmbedded and Industrial Computing{unsigned char temp1;temp1 = (read_sio_reg(0x08,0xE5) & 0x0F);return temp

33Digital Input/Output ControlAppendix CEmbedded and Industrial Computingcase ‘a’:case ‘A’:Output_value = 10;break;case ‘b’:case ‘B’:Output_value = 11

34Terms and ConditionsAppendix DEmbedded and Industrial ComputingAppendix D: Terms and ConditionsWarranty Policy All products are under warran

35Terms and ConditionsAppendix DEmbedded and Industrial ComputingRMA Service Request Form When requesting RMA service, please fill out the following

1IntroductionChapter 1Embedded and Industrial ComputingChapter 1: IntroductionThank you for choosing the LEC-7100. The LEC-7100 is Lanner’s

2IntroductionChapter 1Embedded and Industrial ComputingPackage ContentsYour package contains the following items:LEC-7100 Embedded System •DC+12V 60W

3IntroductionChapter 1Embedded and Industrial ComputingFront Panel FeaturesF2F3F4F6F1F5 F7F1 VGA Port: DB-15 Female ConnectorUsing suitable DB-15 ca

4IntroductionChapter 1Embedded and Industrial ComputingRear Panel FeaturesR1R2R5R6R3F4R1 Reset SwitchIt is a hardware reset switch. Use this switch t

5IntroductionChapter 2Embedded and Industrial ComputingChapter 2: Hardware SetupPreparing the Hardware InstallationTo access some components and perf

6IntroductionChapter 2Embedded and Industrial ComputingNote: To remove the module from the system, release 1. the latch first by slightly bending it