Lanner LEC-3010 Manuel d'utilisateur

>>Embedded & Industrial ComputingHardware Platforms for Embedded and Industrial ComputingLEC-3010V 2.0User's ManualPublication date:　2

8Motherboard InformationChapter 3Embedded and Industrial ComputingMotherboard LayoutThe motherboard layout shows the connectors and jumpers on

9Motherboard InformationChapter 3Embedded and Industrial ComputingRear Side of the Main BoardDC/DC converter board41.625.69989.27Board dimension unit

10Motherboard InformationChapter 3Embedded and Industrial ComputingJumper SettingsSATA (J1) : The system supports one SATA II drive SODIMM1: The SO-D

11Motherboard InformationChapter 3Embedded and Industrial ComputingClear CMOS (JP1): The motherboard contains a jumper that can erase CMOS data

12Bios SettingsChapter 4Embedded and Industrial ComputingChapter 4: BIOS SettingsAccessing the BIOS menuUse the BIOS Setup program when you ar

13Bios SettingsChapter 4Embedded and Industrial ComputingThe Main MenuThe main BIOS setup menu is the first screen that you can navigate. Each main BI

14Bios SettingsChapter 4Embedded and Industrial ComputingOption DescriptionDisabled Set this value to allow the hard disk drive to be used n

15Bios SettingsChapter 4Embedded and Industrial ComputingPrimary and Secondary IDE Master and Slave SettingsFrom the IDE Configuration screen, pr

16Bios SettingsChapter 4Embedded and Industrial ComputingNote: For drive capacities over 137 GB, your AMIBIOS must be equipped with 48-bit

17Bios SettingsChapter 4Embedded and Industrial ComputingOption DescriptionAuto Set this value to allow the BIOS to auto detect the DMA mode

TTaTTable of Contentsbeable of ContentsiChapter 1: Introduction 1System Specication . . . . . . . . . . . . . . . . . . . . .

18Bios SettingsChapter 4Embedded and Industrial ComputingOption DescriptionAuto Set this value to allow the BIOS to auto detect hard disk driv

19Bios SettingsChapter 4Embedded and Industrial ComputingSuperIO ConfigurationSerial Port1 AddressThis option specifies the base I/O port address and

20Bios SettingsChapter 4Embedded and Industrial ComputingUSB ConfigurationYou can use this screen to select options for the USB Configuratio

21Bios SettingsChapter 4Embedded and Industrial ComputingOption Description10 Sec When set to 10 Sec, the BIOS will wait for up to 10 seconds for the

22Bios SettingsChapter 4Embedded and Industrial ComputingBoot Display DeviceIn order to always be able to see POST and Windows boot progress on the

23Bios SettingsChapter 4Embedded and Industrial ComputingBoot SettingsSelect the Boot tab from the setup screen to enter the Boot BIOS Setup screen. Y

24Bios SettingsChapter 4Embedded and Industrial Computingthe host adaptor’s ROM setup utilityBoot Device PrioritySelect this tab to specify the or

25Bios SettingsChapter 4Embedded and Industrial ComputingSecurity SettingsSelect Security Setup from the Setup main BIOS setup menu. All Sec

26Bios SettingsChapter 4Embedded and Industrial ComputingExit MenuSelect the Exit tab from the setup screen to enter the Exit BIOS Setup screen. Yo

27Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AAppendix A: Programming Watchdog TimerA watchdog timer is a piece of ha

1IntroductionChapter 1Embedded and Industrial ComputingChapter 1: IntroductionThank you for choosing the LEC-3010. The LEC-3010 is an industrial com

28Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AChoose to select the hardware Manually8. Choose Show all device and click Next.

29Programming Watchdog TimerEmbedded and Industrial ComputingAppendix ASelect the Lanner IO driver and click Next.14. Click Next15. Click 16. Complet

30Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AWatch Dog sample code:// LEC3xxx_Test.cpp : Defines the entry point for the con

31Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A Run_LED (0, 0) ; Run_LED (1, 0) ; } else if (argv[1][0] == ‘3’)

32Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingAppendix B: Digital Input/Output Control on the GPIO portThe Digitanl I/O on

33Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingChoose to select the hardware Manually8. Choose Show all device and click Nex

34Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingSelect the Lanner IO driver and click Next.14. Click Next15. Click 16. Compl

35Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingA DIO sample code: // LEC3xxx_Test.cpp : Defines the entry point for

36Digital Input/Output ControlAppendix BEmbedded and Industrial Computing Sleep (1) ; } Run_LED (0, 0) ; Run_LED (1, 0) ; } els

37Driver InstallationAppendix CNetwork Application PlatformsAppendix C: Driver InstallationChipset Driver InstallationTo install the Intel® chip

2IntroductionChapter 1Embedded and Industrial ComputingPackage ContentsYour package contains the following items:LEC-3010 Embedded System •Din-Rail Mo

38Driver InstallationAppendix CNetwork Application PlatformsLAN Adapters Driver InstallationThis section provides the instructions on how to

39Driver InstallationAppendix CNetwork Application PlatformsLinuxFollow these instructions to install the Realtek® LAN controller base driver

40Terms and ConditionsAppendix DEmbedded and Industrial ComputingAppendix D: Terms and ConditionsWarranty Policy All products are under warran

41Terms and ConditionsAppendix DEmbedded and Industrial ComputingRMA Service Request Form When requesting RMA service, please fill out the following

3IntroductionChapter 1Embedded and Industrial ComputingF1 VGA PortUsing suitable DB-15 cable, you can connect an appropriate device such as a monitor

4IntroductionChapter 1Embedded and Industrial ComputingTop and Bottom Panel FeaturesR1 Reset Switch: A hardware reset switch Use a pointed object t

5IntroductionChapter 2Embedded and Industrial ComputingNote: SO-DIMMs installed should meet the required 1. speed which is 667 MHz. Do not install SO-

6IntroductionChapter 2Embedded and Industrial ComputingConnecting PowerConnect the LEC-3010 to a 12~36 VDC power source. The power source comes from t

7Motherboard InformationChapter 3Embedded and Industrial ComputingChapter 3: Motherboard InformationBlock DiagramThe block diagram depicts the rela