Lanner LEC-2280 Manuel d'utilisateur

>>Embedded & Industrial ComputingHardware Platforms for Embedded and Industrial ComputingLEC-2280V1.0User's ManualPublication date:201

10Board LayoutChapter 3Embedded and Industrial ComputingChapter 3: Board LayoutConnectorsThe following picture highlights the location of the COM por

11Board LayoutChapter 3Embedded and Industrial ComputingExternal ConnectorsThe following picture highlights the location of system input/output

12Board LayoutChapter 3Embedded and Industrial ComputingInternal Connectors and JumpersThe following picture highlights the location of internal

13Board LayoutChapter 3Embedded and Industrial ComputingInternal Connectors and Jumpers (backside)The following picture highlights the location o

14Board LayoutChapter 3Embedded and Industrial Computing Connectors and Jumpers ListThe tables below list the function of each of the board

15Board LayoutChapter 3Embedded and Industrial ComputingSCT1, SCT2: Select COM1 Protocol SettingRS-232 RS-422RS-485SwitchProtocolSCT1 SCT2RS-232 (defa

16Board LayoutChapter 3Embedded and Industrial ComputingJP1, JP2: Select COM1 and COM2 Pin No9 (Ring Indicator) function respectivelyJP1 JP2Pin Signal

17Board LayoutChapter 3Embedded and Industrial ComputingThe controller contains two modes of operation—a legacy mode using I/O space, and an AHC

18Board LayoutChapter 3Embedded and Industrial ComputingDVI-D Connector (DVID1): A single link DVI-D ConnectorPin No. Description Pin No. Description1

19Board LayoutChapter 3Embedded and Industrial ComputingMPCIE1: Mini-PCIe Connector with SIM Card ReaderPin Signal Pin Signal1 WAKE# 2 VCC3.33 N/A 4 G

2AboutAboutEmbedded and Industrial ComputingOverviewIcon DescriptionsThe icons are used in the manual to serve as an indication of interest topics

20Board LayoutChapter 3Embedded and Industrial ComputingIgnition Connector on board (ignition1): Power ignition connector.SATA_PW2: A switch for s

21Hardware SetupChapter 4Embedded and Industrial ComputingChapter 4: Hardware SetupPreparing the Hardware InstallationTo access some components and p

22Hardware SetupChapter 4Embedded and Industrial ComputingNote: To remove the SIM card, slide the card reader outward to unlock it.PCI/PCIe

23Hardware SetupChapter 4Embedded and Industrial ComputingInstalling the Hard DiskThe system can accommodate one Serial-ATA disk. Follow these steps t

24Hardware SetupChapter 4Embedded and Industrial ComputingWall MountingThe product ships with wall mounting kit. To mount your product on the wall, f

25Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AAppendix A: Programming System Watchdog Timer A watchdog timer is a piece

26Terms and ConditionsAppendix BEmbedded and Industrial ComputingAppendix B: Terms and ConditionsWarranty Policy All products are under warrant

27Terms and ConditionsAppendix BEmbedded and Industrial ComputingRMA Service Request Form When requesting RMA service, please fill out the following f

TTaTTable of Contentsbeable of Contents3Chapter 1: Introduction 4System Specication . . . . . . . . . . . . . . . . . . . . .

4IntroductionChapter 1Embedded and Industrial ComputingChapter 1: IntroductionThank you for choosing the LEC-2280. The LEC-2280 is an upgra

5IntroductionChapter 1Embedded and Industrial ComputingPackage ContentsYour package contains the following items:LEC-2280 Fanless Embedded System •Ser

6System ComponentsChapter 2Embedded and Industrial ComputingChapter 2: System ComponentsSystem DrawingMechanical dimensions of the LEC-2280Unit: mm2

7System ComponentsChapter 2Embedded and Industrial ComputingBlock DiagramThe block diagram depicts the relationships among the interfaces and m

8System ComponentsChapter 2Embedded and Industrial ComputingFront ComponentsComponent Description Pin Definition ReferenceF1 HDD (Yellow) and Power L

9System ComponentsChapter 2Embedded and Industrial ComputingRear ComponentsComponent Description Pin Definition ReferenceR1 DC-In (power) 1x2 Pin